Ghost 2 Immobiliser Reviews
The ghost 2 immobiliser is a cutting-edge anti-theft system that uses modern technology to ward off car theft. This discreet device is undetectable by thieves, and it only starts your engine after a PIN number or app is entered.
It connects to the CAN data network of your vehicle and is weatherproof. It also has the service/valet mode that allows you to temporarily start your car when it's in the garage for cleaning or servicing.
Easy to install
The Ghost immobiliser is a cutting-edge security tool that shields your vehicle from hacking, cloning, and key theft. It uses an exclusive PIN code system that is incorporated into your car's ECU, making it difficult for thieves to spot or tamper with. It is not visible and does not require any sensors or special keys. It's also less expensive than replacing an ECU or installing a new key fob and could lower your monthly insurance premiums.
When installing a Ghost 2 immobiliser, be sure to follow the manufacturer's directions carefully. This will ensure the device is working correctly and efficiently. Test the system after installation by entering the PIN number and then starting the vehicle. Regular testing will help you identify any issues before they get worse.
Before beginning the installation, make sure you check the location of the CAN H and CAN L wires. They are vital for powering the immobiliser, therefore it is vital that they are connected correctly. Labeling the wires will aid in locating them during installation. Once you've identified the locations of these wires, connect them to a permanent 12V power source and the grounding point. Make sure you use a fuse tap if needed to protect the connections from damage or short circuits.
After connecting the wires, tidy up the wiring with cable ties to stop interference. It is also recommended to cover the wires with insulation tape or heat shrink tubing. This will shield the device from electrical shorts, and will extend the life of the device. It's a good idea to test your Ghost 2 immobiliser once the wiring has been secured.
The Ghost 2 immobiliser offers a service mode in situations where you may need to sell your vehicle for example, when it is being repaired or valet parked. This will disable the PIN sequence temporarily. To activate this feature, press the brake pedal while holding the accelerator, and press a number of times that is equal to the first number of the emergency code. The system will then go into service mode, which can be confirmed by flashing the indicator signal 5 times.
It is simple to change PIN codes
A ghost 2 immobiliser is a great way to protect your car from thieves. It is hidden inside the vehicle and can be accessed using a specific code. The device communicates directly with the vehicle ECU through its data bus. It does not rely on radio frequency signals as do traditional Thatcham immobilisers, or aftermarket alarm systems. This makes it difficult for thieves to discern the click of an immobiliser relay or add new key fobs. The control unit is hidden within the wiring harness or dashboard, and cannot be physically tampered with to reset the system.
The ghost 2 immobiliser connects to the vehicle's CAN Data network. It makes use of buttons on the door panels, the steering wheel and centre console, to create a customisable series of up to twenty button presses that need to be entered to start the engine - just as a PIN. This unique next generation system does not require wire cutting upon installation and is fully reprogrammable at anytime. You can also put your vehicle in Valet or Service mode to allow it to start temporarily while you are giving it to a mechanic for work.
You can also use the app to change your PIN code, or deactivate it completely if you've lost your keys. This feature is particularly helpful in the event that you've lent your car away to someone else to use for valet service or parking. It stops them from starting the car and driving it away without your permission. It's also unnoticeable to professional thieves as it does not make use of radio frequencies or circuit cuts.
The ability of the immobiliser prevent relay thefts is another excellent feature. Relay theft is a typical method of car theft in which criminals hack into the diagnostic port on your car, then modify the signal that is sent by the key to the vehicle's ECU in order to trick it into thinking that there is a valid key. This is how traditional immobilisers can be removed, however with a ghost 2 immobiliser, the signal is delayed before it reaches the ECU.
Easy to use app
Ghost 2 is a revolutionary immobiliser that protects your car from key-cloning, hacking, and key theft. It connects to the CAN data network of your vehicle and requires a PIN code in order to start the engine. It also stops thieves from using signal spoofing and device spoofing which are common techniques used to steal vehicles.
The system is simple to use and operates similar to a standard car alarm. Installing the system will allow you to create a unique 20-digit PIN code that must be entered prior to starting the vehicle. This will prevent the vehicle from being taken even if the keys are removed. You can turn off the system by downloading an app on your smartphone.
In contrast to other systems that are silent, the ghost is quiet and does not emit any radio frequency signals. It is a weatherproof, discrete device that can be placed anywhere inside your vehicle. It can be hidden in the dashboard, behind the door panels or the steering wheel. It communicates with your ECU over the CAN data circuit, and is not affected by diagnostic tools that some thieves use to find security systems. It is also not affected by jamming devices that alter codes.
It is a covert installation that doesn't require any wire cutting or modification to the vehicle it can be utilized as an anti-theft system for all vehicles. The technology has been proven efficient, and it's in compliance with TASSA Standards. The ghost is a great solution for classic, sports and prestige cars. It can be used to safeguard vehicles that are hired out through apps such as Turo.
The Autowatch Ghost 2 is the next generation in car immobilisers. The system is unnoticeable to thieves and prevents them from starting your vehicle until they have your PIN or have been authorized by the app. It also doesn't emit radio frequencies or other signals that can be detected by scanners. The process of installing the app is simple and quick. The app is simple to navigate and offers a user-friendly interface which makes it simple to install and use. It also comes with a GPS tracker that can help police locate and recover the vehicle.
Easy to reset
Ghost 2 immobilisers are an excellent way to safeguard your car from being stolen. It integrates into your vehicle's ECU, creating a barrier that thieves can't breach without the correct pin. The device is TASSA certified which means it's recognized by insurance companies. autowatch ghost 2 installers near me 's a powerful device to prevent car theft, and it could save you a significant amount of money over the long term.
In contrast to traditional alarms and immobilisers that require cutting circuits and circuit cutting, the Ghost system is directly connected to the vehicles CAN data network. It works by using the buttons you already have on the dashboard and steering wheel. You can set up a unique PIN sequence, which can be up to 20 presses long. This PIN is required to be entered before the engine can be started like the credit card's PIN. The Ghost system is completely inaccessible to thieves and has no LEDs to signal its presence. This makes it the most reliable aftermarket CAN-bus immobiliser available today.
Another advantage of the Ghost system is that it does not make use of radio frequency signals, which means it is not detected or scanned by thieves. This can prevent cloned keys and relay attacks as well as the more usual method of hacking into a car's CAN bus system by looking for signals from the alarm or immobiliser. Additionally, the Ghost system is designed to be completely hidden inside your vehicle and there aren't any lights or other signals that signalize its presence.
The system also has an option for a Transport Mode that disables the Ghost system that is helpful in situations when you need to temporarily disable it, such as when you are traveling or performing maintenance. This mode isn't as effective as Service Mode as it doesn't deactivate the Ghost system if you exceed 31 mph in 15 minutes.
You will need the emergency code from your installer to reset your Ghost 2 immobiliser. It is typically hidden under an area for scratch-offs on the card provided with your installation. This emergency code should be kept secure and stored in a secure place, such as a wallet at home.